National Institute of Securities Markets

Institute of Securities Markets

A new approach of modernity in planning & construction Dr K M Soni, Chief Engineer, CPWD, Mumbai

National Institute of Securities Markets (NISM) is an educational initiative of SEBI (Securities Exchange Board of India). In securities markets, NISM is already recognised all over the world.

NISM entrusted the work of project management consultancy to Central Public Works Department (CPWD), a government organisation. M/s Hiten Sethi & Associates were appointed as consultants of the project.

NISM was allotted 70 acres land by MIDC (Maharashtra Industrial Development Corporation) at Patalganga, Rasayani in Raigarh district located at about 75 kms from Mumbai International Airport on Mumbai-Pune expressway and is on right side when one travels from Mumbai to Pune. Though almost adjoining to the expressway, there is no direct entry to the campus from the expressway due to government regulations, hence one has to enter the campus from the village side. The land is in three plots, measuring 53 acres, 10 acres, and 7 acres. The institutional buildings and hostels were designed in the plot of 53 acres while residential buildings in 10 acres plot. Plot of 7 acres area has been reserved for future expansion.

NISM campus
Figure 1: Designer's view of NISM campus

Architectural Concept

As shown in Fig. 1, the architectural concept of main campus is based on an axis passing through orientation block, centre of academic blocks and library. All infrastructure facilities are planned on both sides of this axis. There are two gates, one main gate which is near orientation block and rear gate near hostels. The recreation block and library are planned in such a way that they are close to the hostels. The hostels are connected through a corridor to amphitheatre, dining hall, and academic blocks. Main entry to the campus for the visitors is through orientation block in front of which two water bodies are created.

The following facilities are designed in 53 acre plot;
  • Orientation block
  • Academic blocks (4 Nos, housing administrative offices also)
  • Library
  • Amphitheatre
  • Auditorium
  • Dining hall
  • Hostels (3 No’s for students and 1 for MDP executive trainees, total of about 1000 capacity)
  • Recreation block
  • Utility block for services
Residential block having 42 flats and director’s bungalow are designed in 10 acres plot. To avoid large cutting, levels of various buildings have been adopted as per the topography of the area. The buildings are planned as four star green GRIHA rated buildings. Total sanctioned cost of the project is ₹315 crores which includes cost of interiors, furniture and furnishing and agency charges.

Structural concept

All the buildings are designed as RCC structures with required earthquake-resistant design. The hostels and residential block are G+7 storeyed structures while academic blocks and orientation block as G+2 storeyed structures. Dining hall is designed below open air theatre to utilise the space.

All the buildings except utility block are designed as air conditioned buildings.

post tensioned
Figure 2: Casting of post tensioned slab in progress

Some portions of the slabs of the academic blocks have been designed as post tensioned slab (Fig. 2). It has given the advantage of higher headroom required for air conditioning.


To avoid excavation during repair and for easy maintenance, all the services like external water supply, fire and electric cables except sewer lines were taken through trenches.

New Building Materials

Speciality of the project was use of large numbers of new and innovative materials both in construction and interiors. Some of them are being discussed below:

Autoclaved Aerated Concrete (AAC) Blocks

Factory made AAC blocks (Fig. 3) have been used in all masonry work. The blocks have low density (about 550 kg per cum) and are eco-friendly. Apart from the light weight, they have good acoustic and insulation properties. The blocks reduce the weight of structure and also produce quality construction.

residential block
Figure 3: Use of AAC blocks in residential block

Glass Fibre Reinforced Concrete (GFRC) Panels

GFRC panels have been used in the façade of orientation block. As may be seen in Fig. 4, external surface is curvilinear, and thus, a material for cladding was searched which may fit exactly the architectural design envisaged. Simultaneously, it was the requirement that the material is weather-proof and durable. Due to suitability of GFRC panels, they were adopted as they could be manufactured in any shape.

GFRC panels
Figure 4: GFRC panels in the façade of orientation block

Hot dipped galvanized M.S framework and brackets were used for supporting the GFRC panels. Minimum thickness of GFRC panels was adopted as 15 mm, whereas, thicknesses at return flange/embedded location was kept as 50 mm. The panels were strengthened by providing sufficient nos. of horizontal and vertical stiffeners of stainless steel grade 316 of required shape and size as per design requirement.

The panels consisted glass fibers of @ 3.5 to 5% by weight, silica, white cement and admixtures. Water repellent coating was applied on the panels by dipping panels in required solution to withstand atmospheric conditions.

Post tensioned slabs

As already mentioned, post tensioned (PT) slabs were used in some portions of academic blocks. This provided additional headroom for the services. Additionally, such construction has advantages of higher clear spans, thinner slabs, lighter structure, reduced cracking and deflections, reduction in storey height resulting into more storeys in same height, rapid, quality and skilled construction, and higher loading performance. It has to be ensured that the slab is not drilled during lifetime of the structure as it may damage pre-stressing (Fig. 5) and lead to failure.

Casted PT slab
Figure 5: Casted PT slab an academic block

After placement of steel and tendons, concreting is first done except at the end from where stressing is done, excess length cut and grouting carried out around the tendons.

False ceiling and wall panelling

Designed false ceiling
Figure 6: Designed false ceiling in orientation block

Anutone Salon
Figure 7: Anutone Salon Slats Plus false ceiling

Large numbers of patterns have been used for false ceiling and wall panelling in the project providing elegant looks as shown in Fig. 6-13. Some of the special false ceilings used are Anutone Salon Slats Plus false ceiling and panelling in selected lecture halls, recreation block etc. Cloud false ceiling has been used in the dining hall.

Cloud false ceiling
Figure 8: Cloud false ceiling in dining hall

Designed false ceiling
Figure 9: Designed false ceiling in Board Room

In the auditorium, not only false ceiling and acoustic arrangement but interior provides an elegant look.

Panelling pattern
Figure 10: Panelling pattern in lobby of academic blocks

Anutone panelling
Figure 11: Anutone panelling in lecture halls

Panelling and column
Figure 12: Panelling and column cladding in the lobby of auditorium

interiors of auditorium
Figure 13: False ceiling, stage flooring and other interiors of auditorium


Various types of new and innovative floorings have been used in the project including traditional flooring like vitrified tiles and granite floorings. Special flooring includes squash court flooring (Fig. 14 ), wood plastic composite flooring (Fig. 15 ), wooden flooring (Fig. 16), pattern of polished, flamed and leather finish granite flooring, Italian marble flooring etc.

Mapple hardwood
Figure 14: Mapple hardwood squash court flooring

Wood plastic
Figure 15: Wood plastic composite flooring on swimming pool deck

Wooden flooring
Figure 16: Wooden flooring in faculty room

Expanded Polystyrene (EPS) Geofoam Blocks

Such blocks have been used in lecture halls (Fig. 17 and 18) on first and second floors of the academic blocks for construction of steps. The blocks are very light, and thus, help in weight reduction. Due to light weight, their handling and placing is also easy. In the present case, density of the blocks used was 21.6 kg per cum.

Geofoam blocks
Figure 17: Laying of Geofoam blocks

Figure 18: Finished steps with Geofoam blocks
Despite its light weight, the material’s compressive resistance ranges from about 15,178 to 128,223 Pa at one percent strain. When used in the steps, the thickness of the blocks should be as per the requirements of the riser and laid accordingly so that riser of the step is sum of thickness of the blocks, wire mesh and screed concrete including thickness of flooring if any or carpet as proposed. Over the blocks, wire mesh is used to tie them, to keep in position and also for better bonding with the concrete being laid over the blocks. Small thickness of concrete is used for protection and flooring to be laid as per the architectural requirements.

When used in the walling, particularly in partition walls similar procedure can be adopted except that wire mesh should be provided on both sides of the wall.

Stamped concrete

Stamped concrete (Fig. 19) or patterned or textured or embossed concrete is provided to resemble a required pattern, may be brick, stone, slate, tile or wood. It is used for footpaths, walkways, driveways etc. In the project, it has been provided at number of locations such as near academic blocks, library, orientation block, open-air theatre etc. It has also been used in the landscape of hard areas integrated with green areas.

Stamped concrete
Figure 19: Stamped concrete in the path leading to library

In laying stamped concrete, base was prepared with RCC, though, if sub grade is found suitable, it can be provided with plain concrete also. Over the concrete layer finished to the grade, colour hardener is added of the required shade in the fresh concrete as specified, troweled and floated. Approved release agent is then applied evenly to the troweled surface before stamping.

While the concrete is still in plastic stage, required stamping tools are applied to the surface and curing carried out as specified.

Structural glazing
Figure 20: Structural glazing in academic blocks

Structural glazing
Figure 21: Structural glazing in the entrance of auditorium


Though glass is a traditional material but its special use in various allocations makes it innovative. Glass has been used in structural glazing (Fig. 20 and 21), staircase of the library (Fig. 22), skylight windows of connecting corridor of the hostels near dining hall, faculty rooms (Fig. 23), balcony railings of the hostels (Fig. 24), partitions in toilets and other places, doors, etc. Glass mosaic tiles have been used in a wall of the swimming pool (Fig. 25)

Glass used in steel
Figure 22: Glass used in steel staircase of the library

Glass partitions
Figure 23: Glass partitions

glass in balcony
Figure 24: Use of glass in balcony railing of the hostels

Glass mosaic pattern
Figure 25: Glass mosaic pattern on a wall of swimming pool

Other new materials

Apart from the above, PVC drain covers in the overflow drain of swimming pool (Fig. 26), acoustic boards in library (Fig. 27), steel staircase with glass balustrade in staircase of the library, Wi-Fi-enabled class rooms, Aluminium louvers in academic blocks (Fig. 28) and dining hall (Fig. 29) etc, have been provided in the project.

PVC overflow
Figure 26: PVC overflow drain covers in the swimming pool

Acoustic panel
Figure 27: Acoustic panel boards in the library

Aluminium louvers
Figure 28: Aluminium louvers in the academic blocks

Aluminium louvers
Figure 29: Aluminium louvers in dining hall

Namaste furniture in lecture halls

Namaste furniture is manufactured by M/s Godrej Interio. It has been provided in all the lecture theatres. The furniture has the speciality of having all the facilities like plugs for laptops, foldable chairs and desks occupying fewer footprints while not in use (Fig. 30 and 31). Interactive learning and broadcasting facilities have also been provided in the lecture halls.

Namaste furniture
Figure 30: Namaste furniture in 78 pax lecture hall

Namaste furniture
Figure 31: Namaste furniture in 150 pax lecture hall

Green Building Features

All green building features have been provided required for qualifying as 4-star and the project registered for 4-star GRIHA rating. Some of the green features include LED fittings, AAC blocks, green building materials, sewage treatment plants, rain water harvesting system, solar water heating and solar PV panels systems, water recycling, energy efficient air-conditioning system etc.

Inauguration: The project was completed in December 2016 and inaugurated by the Prime Minister in presence of Finance Minister, Governor of Maharashtra and Hon’ble Chief Minister of Maharashtra.

At present, the campus is fully functional.


Tender Documents for the work invited by CPWD

NBM&CW October 2018

Click Here
To Know More / Contact The Manufacturer
Please provide your details we will contact you as soon as possible
Please let us know your name.
Invalid Input
Please let us know your Designation.
Invalid Input
Please let us know your City.
Please let us know your State.
Please let us know your Country.
Please let us know your Contact Number.
Please let us know your email address.
Please brief your query.

Building Materials, Testing & Sustainability

This comprehensive textbook by well-known and award-winning author, design consultant, and researcher, Dr, N Subramanian, is an invaluable source of knowledge for engineering students, architects, consultants, researchers, teachers, and all those Read More ...

Turning Plastic Waste into Eco-friendly Building Materials & Products

Since the past 65 years, about 8.3 billion tons of plastics have been produced worldwide, which is equivalent to 10,000 Eiffel Towers or 35,000 Empire State Buildings. But only 9 percent of all plastics gets recycled, while the rest ends up as trash Read More ...

Lessons from Warfare to Manage Complex Marketing Projects

The fundamental definition of warfare is to compete and win over enemies with limited resources. Interestingly, it is fundamental to running a marketing function in a corporate company. My fellow marketing heads will agree that it is imperative Read More ...

Lightweight Fiber-Reinforced Houses

lex Liew Chung Meng, an innovator of Lightweight Concrete Methodology (LCM) for low-cost housing, has been approached by a Kolkata-based construction company, which has secured an order to build 18,000 low-cost housing units. To Read More ...

Water Management in High-Rise Buildings

According to a recent report by Niti Aayog, India is suffering from the worst water crisis in its history, with around 600 million people facing severe water shortage. If this continues, there will be a 6% loss in the country's GDP Read More ...

A Revolution in Concrete Floors-Free Movement (FM) and its Importance

With growth and Industrialization, the demand of industries has been increasing, especially for the fast-track projects. Consequently, the importance of flooring (mainly concrete flooring) in the operation of the industries is Read More ...


Smart living through smart products and services is today a worldwide trend being promoted by IT companies. These companies are putting lot of efforts and resources to create useful digital solutions for promoting business Read More ...

Aerial Rope Transit - (Cable Car) for Public Transport

Aerial Rope Transit - (Cable Car) for Public Transport Advanced transport technologies have improved mobility of men and materials in both normal and specific conditions. Numerous transit technologies have been Read More ...

The New Rural Reality: Impact of Digitisation

Tapan is a middle aged resident of Bhogpur village in District Purba Medinipur, 75 kms from Kolkata, involved in his traditional family business of farming. For several years he had been visiting his nearest Read More ...

Seismic Vulnerability Assessment and Strengthening of Existing Reinforced Concrete Buildings

Some of the severe earthquakes that occurred across the world after the year 2005 are Nepal M 7.8 (2015), Haiti M 7.0 (2010), Southern Sumatra, Indonesia M 7.5 (2009), Eastern Sichuan, China M7.9 (2008), and Java, Indonesia Read More ...

Catalyzing Employability through Infra, Social and Rural Development Projects

With 65% of India’s population composed of youngsters facing job deficit, our demographics dictate that infrastructure, social and rural development projects can be one the important role models for solving Read More ...

Seismic Design Concept for Non-Structural Connections using Post-installed Anchors

As the seismic activity in and around India, has been steadily increasing, the government has taken the initiative to conduct several workshops and trainings to spread awareness on the subject. Seismic design of Read More ...

IESC: Transforming the skill landscape

Over the years, growth in the infrastructure equipment sector has been synonymous with the economic health of the country. In 2010, the sale of construction equipment was around 60,000 units and expected Read More ...

Effects of Blast Loading on Engineering Structures – An Overview

The present study aims at providing an overview on the blast loading and blast effects on engineering structures. The use of vehicle bombs to attack city centers has been a feature of campaigns Read More ...

Characteristics study of Stabilized and Compressed Laterite Soil Bricks

There is a need for development of alternative materials for the building industry with low carbon footprint and at the same time to save energy. Clay has been used as a building material from the beginning Read More ...

Behavior of Reduced Beam Section Moment Connection With Varying Thickness of Continuity Plate

Reduced beam section (RBS) connection is investigated and is widely used in US, Japan and Europe. However, very limited study is conducted with respect to Indian profiles. This study is conducted Read More ...

New Building Material & Construction World

New Building Material & Construction World
MGS Architecture

Modern Green Structures & Architecture

Modern Green Structures & Architecture

Lifting & Specialized Transport

Lifting & Specialized Transport

Indian Infrastructure & Tenders Week

Indian Infrastructure & Tenders Week