Interfacial Zones and Concrete Waterproofing by Buildcore Chemicals

Salim Jawadwala Builcore Chemicals
Salim Jawadwala, Builcore Chemicals
Waterproof concrete technologies can be as complicated as the pore and capillary structures within the concrete. There are many systems, ideas and theories on how to achieve waterproof concrete. Many of the theories and products regarding waterproofing of concrete fall short of their objective when we consider the interfacial zones within the concrete.

Interfacial zones are the areas where aggregate and cement particles meet face to face. The interfacial zones are considered a weakness in terms of strength and permeability. Even concrete that has a low w/c ratio and strong aggregate is only as good as the bond between them. If the interfacial zone is poor, the concrete will be subject to increased permeability, and lower strength.

When considering concrete strength and waterproofing within the interfacial zone we must also consider the particle packing effect.

Concrete Waterproofing Builcore Chemicals
The Particle Packing Effect (also known as the "Wall Effect")
The particle packing effect is due to the inability of the cement particles to pack efficiently near the aggregate. The size of the cement particles are much smaller than even the finest aggregate, so by comparison the aggregate has many areas that can be considered flat edged. These are the areas that suffer from poor packing. Of course, the larger the aggregate, the more dramatic the effect. The lower amount of cement particles near the aggregate directly correlates with a higher w/c ratio in the paste near the aggregate. The closer to the aggregate, the stronger the effect. As the concrete hydrates, these areas which have lower amounts of cement particles (resulting in higher w/c ratios) have higher capillary porosity in relation to the rest of the concrete mass. Bleed water during hydration may also form a layer over the aggregate which then results in even more porosity through bigger and more pores and capillaries.

To summarize the weakness of interfacial zones, we know that the regions around the aggregate have increased w/c ratios due to lower clustering of cement particles resulting in increased pore and capillary sizes as a direct result of the higher w/c ratios. The hydration effects in the areas around the aggregates are not as complete as they are in the concrete mass. We also know that bleed water can further affect the hydration around the aggregate. This further results in a less hydrated, weaker cement paste near the aggregate and has a negative effect on the bond of the cement paste to the aggregate. These areas become the weak link in the concrete chain and will be more susceptible to damage by water and other related problems such as chloride ion ingress, alkali silicate reaction, freeze/thaw cracking, and spalling to name just a few. It will also affect the concretes strength and the overall durability of the concrete.

It can be clearly argued that if we can increase the CSH development in the interfacial zones, we can thereby reduce the negative effects of particle packing resulting in an increased overall strength and impermeability which are directly linked to the long-term durability of the concrete.

So the question then becomes "how do we increase the CSH development within the interfacial zones". The idea of lowering the w/c ratio of the concrete may be one of the first ideas that comes to mind, but this is subject to limitations. In theory, when we reduce the w/c ratio to the point that we have restricted the connectivity and reduced the size of the pores and capillaries within the cement paste to be considered impermeable, the concrete should be waterproof. In practice however, the waterproofing capabilities of the concrete needs to take into account the effects of the aggregate interfacial zones. If we consider that data is available showing that concrete can have up to 100 times the water permeability of the cement paste it is made from, it is easy to discredit lower w/c ratios as a solution to interfacial zones. We must also consider the issues of low w/c ratios on the autogenous shrinking of the concrete. This does not even take into account any other considerations (such as cost) that come with lower w/c ratios. It seems fairly clear that water may still have access into the concrete even though the cement paste may have a very low porosity. The waterproof concrete we have made turns out to be more permeable than we expected. This also means that methods of lowering the w/c ratios such as using water reducers, and super plasticizers cannot contribute to a significant solution for the interfacial zones.

In considering how to increase the CSH in concrete, there are several potential technologies available. These include densification materials (such as silicate based technologies), and pozzolans ((such as GGBFS (ground granulated blast furnace slag)).

Let us first consider the densification approach as a potential method to increase CSH in the interfacial zones. These types of materials when added as an admixture, react with the free lime in the concrete to densify the concrete and, in theory, work to fill the pores and capillaries with CSH gel. When we consider that densification systems will be subject to the same particle packing effects as cement particles, and that when using these types of products once the active chemical has reacted there is no further reaction, this means that as a reaction occurs in the cement paste the reactive material cannot transfer towards the interfacial zone as it is blocked and used up by the reaction with the free lime in the capillary spaces where there is a higher concentration of the reactive materials. It will also be affected by a one-sided growth effect in which the densification products can only access the areas around the aggregate from the cement paste sides. The cement paste will have less capillary spaces from the aggregate side limiting access from the side with the aggregate. This reduces further the ability of densifiers to build CSH in concrete's interfacial zones. Densifiers also have the added fault of promoting cracking in concrete through increased heat of hydration associated with accelerated setting times.

There are many types of pozzolans both natural and synthetic. They are as a general rule good for concrete and many will increase CSH growth within the concrete. They also tend to be environment-friendly and reduce cost. Pozzolans (subject to the type) will increase strength, reduce permeability and increase durability to some degree. Pozzolans however are also subject to the same problems as the lower w/c ratio concretes and densifiers. The particle packing effect is still present and the limitation of one-sided growth will reduce their abilities to enhance the CSH growth around the aggregate.

The concept of increasing CSH growth in the concrete to help strengthen the bond between aggregate and cement paste is sound, but the difficulty is in the delivery system. By simply making the concrete more reactive we are still subject to the effects of particle packing and one-sided growth. Therefore, we must consider a method to increase CSH in the interfacial zones that not only increases CSH growth around the aggregate, but also possesses a delivery system that can overcome the particle packing effect and one-sided growth. The ideal solution must be something that can migrate through the pores and capillaries and promote dramatic CSH growth in areas with high porosity and a lower amount of cement particles while not being reactive itself in nature.

Let us now consider Crystalline technology. There are several different types of crystalline technology available in the global market. These can be divided in to densification (hydrophobic) and non densification types (hydrophilic).

Since what we require is a system that migrates through the concrete, we can eliminate all densification type crystalline systems. These are easily recognizable because they really are densification technologies marketed as crystalline and are subject to the same faults as densification technologies when it comes to interfacial zones. They react with the lime in the concrete, they claim to use osmosis as the migrating principle and they do not retard (they usually accelerate) setting time. New generation crystalline technologies are catalytic (not reactive), they use adsorption to migrate through the concrete (not osmosis) and they always retard the setting time of the concrete.

Enhanced Crystalline Growth
Enhanced Crystalline Growth
If we use new generation crystalline technology in the concrete as an admixture, we will see that initially the catalytic component of the crystalline is subject to the effects of particle placement. There will be lower concentrations of the catalytic type crystalline as we get closer to the aggregate. Initially as the concrete hydrates, the areas further away from the aggregate will begin creating enhanced CSH growth quicker and it will slow down as it get closer to the aggregate. Once the catalytic reaction occurs between the cement and the water, the extra water surrounding the aggregate will, through the absorption mechanism, draw the crystalline towards the aggregate creating further reactions between the cement particles and water. Even though there are fewer cement particles near the aggregate, the CSH that has been developed is greatly enhanced offsetting the reduced quantity of cement particles.

The one-side growth effect can also be easily overcome using a hydrophilic, catalytic crystalline that uses adsorption for the migration mechanism. As this type of crystalline is drawn towards water, the higher w/c ratios near the aggregate result in the crystalline being pulled towards the aggregate. This will effectively increase the hydration process near the aggregate and thereby increase the amount of CSH developed in the areas.

Using a new generation crystalline technology, we can effectively overcome interfacial zone weaknesses and thereby strengthen the weakest link in the concrete chain.

NBM&CW September 2016

Click Here
To Know More / Contact The Manufacturer
Please provide your details we will contact you as soon as possible
Please let us know your name.
Invalid Input
Please let us know your Designation.
Invalid Input
Please let us know your City.
Please let us know your State.
Please let us know your Country.
Please let us know your Contact Number.
Please let us know your email address.
Please brief your query.

Buildtech: Pragmatic Approach to the Methodology of Retrofitting Buildings

With the increase in construction of buildings in the last two decades, it has been observed that many of the structures are already showing signs of distress. In some cases, repair measures become necessary even within a span Read More ...

Pure Leathers Waterproofing Solutions for Tunnels, Roofs, Water bodies…

There are various types of Waterproofing Systems available for different applications. Based on its vast experience in waterproofing, Pure Leathers Pvt. Ltd. (PLPL) recommends the most suitable waterproofing systems for various site requirements Read More ...

This monsoon, insure strength for your building with waterproofing & repair solutions from Chowgule

Over a period of time, a building goes through severe climatic changes leading to its ageing, thereby creating loopholes and leakages. A leakage deteriorates the quality of the building, since the water through the affected area, also flows to other Read More ...

STP: Waterproofing & Construction Chemicals

The concept of liquid waterproofing has existed since the early 1800s, when natural bitumen was combined with jute, straw, rag felt and other man made materials to provide a waterproofing solution. Apart from liquid waterproofing membranes Read More ...

Atul: Epoxy & PU solutions for terrace waterproofing with 7-year performance warranty

Water is good while constructing a building, but not so well after the concrete is set. Rain water starts penetrating through the porous concrete in walls and ceiling, creating ugly images of peel-off paints, cracks, damp walls filled with deadly Read More ...

Tremco: Solutions For Problematic Leaking Podiums Latest Technological Advances

India is seeing a spurt in urbanization. As we continue to build bigger, faster and taller, reinforced concrete is the choicest of materials to meet the needs of speed and durability. If we understand concrete simplistically, it consists of the aggregate Read More ...

Long lasting waterproofing solution with Epoxy and PU

Atul Ltd's Lapox® epoxy range of adhesives find the largest application in the construction sector. Products include Lapox® Lacrete and Lapox® Procoat for terrace waterproofing; Ultrafix for vertical cladding Read More ...

Repair & Rehabilitation: STP Ltd

STP provides Waterproofing & Protective Coating solutions for all areas. The range of waterproofing coats consists ShaliRust Off, ShaliPrime ZnR, ShaliBond concrete, Shalifix EM, ShaliGrout EI, ShaliFix RM Read More ...

The Raincoat Advantage

In heavy monsoons, would you be caught wearing a torn canvas jacket? Of course not, what a ridiculous question! You would wear a raincoat. So why not extend the same logic to the building structures Read More ...

Roads & Bridges: Repairing, Waterproofing & Asset Management

Waterproofing Technology is continuously progressing. In this context, several important concepts are illustrated which are of use to technology planners and forecasters. STP Ltd has one of the biggest Read More ...

STP offers Green and Cost-Effective Solutions for Road Construction & Maintenance

Fiscal year 2016-17 started with big reforms and multi-dimensional growth-oriented measures like budget allocation for infrastructure developments, over 10,000 km of roads, waterways, railways, and Read More ...

Black Bond Seal Black Concentrated Resin for Multiple Applications

Bond Seal India Pvt. Ltd. is meeting the demand in the construction industry for protection, maintenance and restoration by offering the right solutions and quality products, and innovating for the future Read More ...

Trelleborg launches Rotary Seal for equipment working under high pressure

Trelleborg Sealing Solutions
Trelleborg’s Turcon® Roto Glyd Ring® V rotary seal is designed for equip to work under high pressure without compromising the sealing performance. Trelleborg Sealing Solutions launched an innovative Read More ...

Polygomma™ EPDM Waterproofing Membranes for various areas of building

EPDM Waterproofing Membranes by Polygomma™ are easy to install and can be used on various areas of a building including basements, podiums/landscape areas, roofs/terraces, wet areas Read More ...

Buildtech offers high quality Liquid Waterproofing Membranes

BUILDTHENE IC-Polyurethane-based & BUILDCOTE EC 20-Acrylic Polymer-based Liquid Membranes are the two new waterproofing products by Buildtech. Buildtech is a trailblazer in the Construction Chemicals Read More ...

STP’s Waterproofing & Coloring Solutions for Roads & Bridges

Shali Seal RSTC Elevated Roads
STP's waterproofing soultions include ShaliSeal RSTC, SuperThermoLay APP membrane, ShaliSeal CSS, ShaliPatch, ShaliPatch EC, to be used on Roads & Bridges. Waterproofing Technology is continuously Read More ...

New Building Material & Construction World

New Building Material & Construction World
MGS Architecture

Modern Green Structures & Architecture

Modern Green Structures & Architecture

Lifting & Specialized Transport

Lifting & Specialized Transport

Indian Infrastructure & Tenders Week

Indian Infrastructure & Tenders Week