Stacy Byrd, Technical Services Director & Amit Bartakke, Regional sales Director – India & subcontinents, CETCO

In recent years expensive remedial work to correct failures in below-grade waterproofing systems has motivated owners and designers to seek high-performance and reliable waterproofing solutions to prevent water ingress. In some cases the remedial costs have been many times greater than the initial cost to install the waterproofing; with remedial results not successful at eliminating all of the water leaks.

The construction industry has utilized passive SBS/APP waterproofing membranes for years with general success, but recent failures have led to the development of hybrid membranes that in some cases incorporate active barrier materials for enhanced performance and reliability.

Most of the problems that arise in waterproofing are due to one or more of the following factors:
  1. Choosing inappropriate waterproofing membranes for the wall casting methods
  2. Construction practices and traffic that damage the waterproofing materials after installation
  3. Designs and materials that are inappropriate for the site conditions
  4. Materials that are installed incorrectly
  5. Construction schedules that do not allow for proper sequence and adequate inspection of the work
  6. Value engineering that eliminates components of the waterproofing system or decreases the quality of the waterproofing system
The cost of waterproofing is generally proportional to performance. Waterproofing systems known for high performance generally are priced the highest within the construction industry. Owners and contractors often seek a bargain when comparing waterproofing materials, but they may not understand that different membranes can produce different results and may not even be suitable for their site conditions. For instance, sheet waterproofing membranes can be substantially more expensive than waterproofing admixtures, but the manufacturers for both systems claim similar results – a watertight structure. But the repair required, and cost, if these systems fail will be quite different. Owners and designers must examine the product components and installation techniques of each waterproofing system with regard to performance, applicability with construction methods, and associated warranties in order to come to an informed decision.

For example, waterproofing admixtures, when introduced into concrete mixes, offer some integral waterproofing capabilities. The waterproofing admixtures work within the concrete to prevent transmission of moisture on a microscopic level by affecting concrete pore structure. The issue with admixture waterproofing is that its effectiveness is limited by how well cracking is controlled. Cracking in foundation walls and slabs creates an entry point through which water can easily migrate. Contractors have found it necessary to use remedial polyurethane foam grouts to repair cracks and stop water infiltration through cast-in-place concrete cold joints. Additionally, since the admixture waterproofing material is not a separate barrier material applied to the exterior wall, surface of the foundation the project team must consider what increased level of corrosion is acceptable in the foundation walls knowing that the water is most likely going to penetrate into the structural foundation concrete wall before it can start to be stopped in cracks by the admixture waterproofing.

Waterproofing Selection Factors

Selection of the waterproofing system typically depends on several key factors, such as the foundation construction method (i.e., blind-side or positive-side backfilled walls), environmental conditions, and geotechnical factors such as the potential for hydrostatic pressure. But ultimately the membrane selection may depend on the Owner’s tolerance for risk of water intrusion versus its installed cost.

Voltex / Voltex DS waterproofing
Voltex / Voltex DS waterproofing installed over substrate prior to raft slab placement.

Prior to selecting a membrane, Owners must consider their tolerance for water ingress and the appearance of water-related effects, such as efflorescence and biological growth, in the project’s below-grade spaces. Typically, the usage of the below-ground space determines the level of acceptability of water ingress. For example, the expectation for water-tightness is drastically different for a hospital than it is for a parking garage.

Site Access: Positive-Side vs. Blind-Side

There are two general installation methods for below-grade waterproofing membranes, typically referred to as positive-side and blind-side (aka zero-lot line). Positive-side application of below-grade waterproofing membranes indicates the installer applies the membrane to a concrete wall surface after the forms are removed on an over-excavated site excavation; while blind-side application indicates the installation of the membrane occurs against an excavated shoring retention wall system, such as auger cast pilings, prior to pouring the basement walls. Under slab membrane placement would also be considered a blind-side application due to the construction sequencing. Waterproofing performance can vary dramatically depending on the application method and material. Positive-side waterproofing is an easier application due to the site access where the membrane can be inspected and repaired prior to backfill. Blind-side waterproofing performance has been more problematic as the placement of the concrete over the membrane does not afford the installer the ability to correct deficiencies. Thus with blind-side waterproofing it is even more crucial that good field quality assurance measures are undertaken prior to and during the concrete placement. It should be noted that membranes that are typically used for positive-side are generally note suitable for blind-side applications due to the reversed installation sequencing that must be undertaken. For example, a peel-and-stick self-adhering sheet membrane is suitable for positive-side applications but that same membrane is not suitable for under slab or blind-side applications.

Voltex / Voltex DS waterproofing membrane
Voltex / Voltex DS waterproofing membrane installed on shoring retention wall prior to foundation wall being cast - blind-side waterproofing application.

Geotechnical Selection Factors

Waterproofing product selection depends heavily upon the potential for hydrostatic conditions. If the project extends several levels below-grade, the project may encounter the water table. The ramification of placing the project into the water table is two-fold: the structural engineer will need to compensate for the additional forces and the waterproofing system will be subjected to hydrostatic pressure continuously or at a minimum intermittently. The requirements for membrane performance predictably increase when placed in the water table, and hydrostatic pressure exacerbates any construction defects.

Some sites possess the potential for differential settlement to occur for various reasons such as soil type or seismic activity. Settlement has important consequences for waterproofing membranes, since a structural slab may experience cracking. Slab cracking can potentially rupture an underslab membrane, allowing transmission of moisture up through the damaged membrane into the interior space above.

Backfilled wall waterproofing by CETCO
Backfilled wall waterproofing by CETCO – Voltex & Voltex DS

Hybrid Waterproofing Materials

To avoid failures and water leaks, new developments in waterproofing membranes such hybrid systems offer designers the ability to compensate for potential weakness in the waterproofing materials with regards to the site conditions and construction method. Below-grade spaces offer few choices for repair due to inaccessibility, and the addition of new waterproofing materials are a welcome addition to the industry.

There are many options available when considering approaches for below-grade waterproofing. It is important that the project team consider their tolerance for risk of water ingress with regards to the foundation construction method, and geotechnical factors when determining the most appropriate waterproofing system. A primary decision factor is the construction method, which will dictate whether blind-side or positive-side waterproofing will be used in conditions where a below-grade waterproofing membrane is required. While traditional membranes have been used successfully in the past and are still viable options, innovations on the part of material manufacturers are presenting new options that compensate for limitations that have led to failures. Hybrid materials appear to create solutions for problematic installations.

The construction industry has utilized self-adhering waterproofing sheet membranes for several decades with general success, but failures and limited performance have led to new material developments. New sheet membranes introduce measures of redundancy performance by combining passive and active materials to create hybrid products. Hybridization of below-grade waterproofing membranes seeks to combine traditional materials in an effort to counter failure trends. By recognizing modes of failure in traditional membranes, new hybrid products hope to prevent failure by incorporating several material types, and thus several different failure modes, in a single membrane. The common trend among all emerging waterproofing systems is a recognized need to perform at a higher performance level.

The trend towards hybrid products originated with bentonite being combined with polyethylene membranes. The advantage of incorporating two layers of waterproofing, regardless of integration into a single membrane, is immediately apparent: two layers of protection are better than one. Combination of waterproofing materials allows the composite membrane to harness the capabilities of each layer while enhancing the performance of both through proximity of placement. CETCO used this approach in their design of Voltex DS, which consists of a polyethylene liner combined with active sodium bentonite interlocked between two geotextiles. In this case, the polyethylene membrane layer resembles traditional passive membranes, while the active bentonite layer reacts to and seals the water that circumvents the polyethylene layer. Thereby, the bentonite layer compensates for imperfections in installation and undetected minor construction damage in the polyethylene membrane.


Another trend is the use of hydrophilic waterstops in the concrete construction joints as a back-up to the waterproofing membrane installed on the exterior surface of the below-grade structure. Waterstop is a material that is embedded in the concrete, across the concrete joint, to obstruct the passage of water through the joint. A waterstop installed in concrete joints is an important component of an overall waterproofing design. Use of a waterstop with a waterproofing membrane is considered a belt-and-suspenders approach to provide a dry basement. This is a common practice to waterproofing design because if for some reason water is able to circumvent the membrane the waterstop is in position to obstruct the water in the most likely place the water leak can occur – through the concrete cold joint.

CETCO Waterstop XP

Bentonite strip Water stop RX 101
Bentonite strip Water stop RX 101 / XP expanded into poorly consolidated concrete.

Recently hydrophilic swelling strip waterstops have gained in popularity due to their ease of installation and wide application utility. Among this type of waterstop are bentonite-based products like Waterstop-RX 101 / XP by CETCO. These active hydrophilic strip bentonite waterstops swell in the presence of water to form a positive seal in the concrete construction joint to obstruct water migration through the joint. Also these strip waterstops can be installed around pipes and irregular shaped mechanical elements that may pass through the waterproofing plane; an application that cannot be accomplished with traditional PVC dumbbell waterstops.

CETCO Waterstop

Remedial Waterproofing Trends

With regards to remedial waterproofing, cement grouts injected to the exterior side of a foundation wall and polyurethane grouts injected directly within the cracks of the foundation wall have been used extensively; both with varying degrees of success. The limitation with polyurethane grouts are that they are injected through a drilled hole that intersects each crack within the wall and may not actually prevent the water from entering the wall. The primary limitation for cement grout is that when it is injected it can be contaminated with the soils around the structure to make it more permeable as well as weaken its bond potential to the exterior surface of the existing concrete. To address these problems there is another remedial injection grout produced with bentonite. The bentonite-grout is injected through a drilled hole to the exterior side of the foundation wall where it fills voids and coats the exterior surface of the concrete. Unlike cement grouts, the bentonite-grout forms a strong adhesion to the outside surface of the concrete that remains plastic and pliable to maintain a positive seal. It is this plastic long term bond properties that separates it from cement grouts that will cure rigid and simply form a concrete cold joint with the existing concrete. Also for some applications the bentonite-grout can be used in conjunction with the polyurethane grout, whereby the polyurethane is injected into the wall cracks and then the bentonite-based grout is injected to the exterior to coat the wall to eliminate water infiltration into the wall to stop further corrosion of the structural foundation. For shallow depths, the bentonite-grout can be injected through a trimie pipe manually placed without excavating.

Importance of Quality Assurance

Contractors may have the most important role with regards to waterproofing – the installation. Waterproofing should be treated as a strategic building material for the long-term success of the project. For waterproofing, proper design, installation and concreting practices must be followed. Additionally, it is very important that the installer’s crew be well trained in the proper installation of the material. If the installer’s crew is not properly trained with regards to the installation of the material, it simply may not matter which product is selected.

One method to improve workmanship is for the project team to implement a quality assurance program for the below-grade waterproofing that forces the waterproofing subcontractor to establish quality standards for the work. This requires, in part, that the subcontractors follow a specific set of workmanship guides established by the material manufacturer. A quality program should require the waterproofer to complete and maintain daily reports on their installation work that includes both site maps and photos. Another practice is to specify and implement a mock-up of the waterproofing installation to set the project work standard and prove that the material can be installed properly to the project conditions. Also the waterproofing subcontractor should prepare full shop drawings so that the field installer has complete understanding of the application. Finally, specify, plan and hold a pre-construction meeting with all the applicable subcontractors that will or could impact the waterproofing installation; and express to all participants the importance of the waterproofing system as it relates to the success of the project. And during the installation timely inspections by a qualified third party inspector should be conducted throughout the course of the waterproofing system installation and backfill placement.

BentoGrout performance“BentoGrout remedial waterproofing grout injected to the exterior of the foundation to stop water infiltration.”


Numerous failures and costly repairs have pushed the construction industry to search for more reliable below-grade waterproofing solutions. Careful consideration of site conditions and construction methodologies can lead to successful selection and installation of below-grade waterproofing membranes so that future remedial work is limited. To avoid failures, new developments in waterproofing membranes, such as dual membrane hybrid systems combining passive and active materials offer the designer the ability to compensate for potential weakness in traditional waterproofing membranes. Finally, a quality assurance program should be planned and implemented to treat the waterproofing as a strategic building material for the long-term success of the project.


Stacy Byrd and Amit Bartakke

Stacy Byrd is the Technical Services Director & Amit Bartakke Regional sales Director – India & subcontinents, a leading manufacturer of waterproofing, green roof systems, composite drainage, and water stops.
Click Here
To Know More / Contact The Manufacturer
Please fill in your details, we will contact you as soon as possible
Choose Title from the listPlease let us know your name.
Please let us know your Designation.
Invalid Input
Please let us know your email address.
Please let us know your City.
Please let us know your Contact Number.
Please brief your query.
Our other value-added services:

To receive updates through e-mail on Products, New Technologies & Equipment, please select the Product Category(s) you are interested in and click 'Submit'. This will help you save time plus you will get the best price quotations from many manufacturers, which you can then evaluate and negotiate.

Equipment & Machinery
Invalid Input
Building Products
Invalid Input
Invalid Input

Concrete Protective Liner by Russian company Hydropolymer

Concrete protective liner is a multipurpose solution for waterproofing and protection of concrete surfaces against corrosion and destruction. The product warranties long-term and reliable protection of structures Read More ...

WATERPROOFING Importance of Filling Cracks, Joints & Voids

Samir Surlaker, Director, Assess Build Chem Private Limited discusses some new joint treatments and injection systems in waterproofing. It is a myth that waterproofing treatments can be carried out by application of single material Read More ...

Dr. Fixit introduces LW+Super for enhancing the efficiency of M-sand

The rapid boom in the construction industry, has tremendously given rise to the demand for sand, causing deficiency of suitable river sand in many parts of India. Besides, river mining causes imbalance in the river bed water flow, and Read More ...

Step towards building a healthy home

A home remains an individual's most cherished asset and biggest investment decision taken. It isn't merely a shelter made up of lifeless bricks and concrete. For an individual and his or her family, the home remains a highly Read More ...

Concrete Protection Coatings for Reinforced Concrete Structures

Reinforced concrete is a composite material. Its structural performance is realised only when concrete and steel act in unison during the service life of the structure. The compressive and tensile loads are carried by Read More ...
Waterproofing application Newcoat

Waterproofing Methods: Modern and Conventional Waterproofing Techniques

We Indians normally go by the adage of ‘old is gold’ and while that may hold true in some instances, it certainly is not true for old, archaic systems of waterproofing. Very often we find that a lot of innovative Read More ...
Sunanda Chemical

Effective Waterproofing for Durable Structures

No material is itself durable or non durable, it is the interaction of the material with its in service environ- ment that determines its durability - says a well known concrete technologist Larry Masters Read More ...
Roof Waterproofing

Roof Waterproofing

The issue of waterproofing of roof has to be dealt with care and one must ensure that the right products are being used in the right manner. Conventionally, the concrete roof slab is covered with Brickbat Read More ...
BASF Sustainable Waterproofing Solutions

Innovative & Sustainable Waterproofing Solutions from BASF

Innovations in chemical technology solutions for civil engineering and construction are meeting demands placed by increasing complexity in structures. One such is in waterproofing, driven both by Read More ...
Hydralastic Concrete Waterproofing

Fielding The Elements: Waterproofing Systems

Waterproofing, is an important part for any construction project looking for a sustainable and well finished product, with a low maintenance life cycle. Correctly done, it offers great value to the quality of structure, Read More ...
Bathroom Wall Treatment

Waterproofing Your Bathroom

Normally the materials and components used in bathroom to make its floor, wall, architectural finishes etc. including service pipes and sanitary fittings are susceptible to natural movement and as Read More ...
Crystalline Concrete Admixture

Crystalline Technology For Concrete Waterproofing

Concrete is one of the most commonly used building and construction materials. However, due to its composition, is often susceptible to damage and deterioration from water Read More ...
chemical admixture in concrete

Commonly Used Chemical Admixtures in Concrete

The modern construction industry uses a variety of chemical admixtures in concrete, to reach desirable qualities along with a view to promote sustainability in it. ASTM C 125 defines an admixture Read More ...
Chemical Admixtures in Concrete

Chemical Admixtures in Concrete A state-of- the-art-report

Concrete, nowadays is not just mixing of cement, aggregate & water but it also comprises of chemical and mineral admixtures. It is becoming a more and more effective construction material as a result Read More ...
PVC Membrane Waterproofing

The Need for Right Waterproofing

How often do we think that why do we need to do waterproofing of a structure or which system of the many available is right? The answer to this can only be arrived at after assessing various factors related Read More ...

Waterproofing – What, Where and How?

Waterproofing is important in protecting the structure and ensuring that the structure is usable over its entire service life. The forces exerted by water are enormous and its effects Read More ...
glass fibre wrapping

Glass Fibre Wrapping Technology

Glass Fiber Wrapping can be used where concrete looses its capacity/design strength due to corrosion change in use and / or the design code demands increases in load carrying capacity. It can also Read More ...

New Building Material & Construction World

New Building Material & Construction World
MGS Architecture

Modern Green Structures & Architecture

Modern Green Structures & Architecture

Lifting & Specialized Transport

Lifting & Specialized Transport

Indian Infrastructure & Tenders Week

Indian Infrastructure & Tenders Week

Please publish modules in offcanvas position.