Bolster or Turntable

Marco J. van Daal, Owner, The Works international

A bolster or turntable is a device (or rather a set of devices) that allows long loads to be transported on two transporters, with a relatively short length, instead of one single transporter with a length (almost) equal to the load. Such a transport is also referred to as a “dolly transport”. The turntables or bolsters allow transporters to pivot underneath the load to negotiate turns and corners and (to a certain extent) super elevation and articulation, as well as inclines and declines.

A turntable consists of two parts: a lower part that is secured to the transporter called the Lower Fixed Part (LFP) and a movable or rotating upper part that is secured to the load, called the Upper Rotating Part (URP). The URP rotates around the center of the whole assembly. The two parts are held in place by a pin or a ball bearing. The contact area between the URP and the LFP is lubricated with grease or oil to allow the rotating motion with minimal friction.

Turntable design
There are three basic turntable designs:
  • The simplest design consists of just two steel plates with a pin in the center. No articulation in either direction is possible (except what the plywood between the saddle and plate allows, crushing). A-type.
  • Turntables with sliding shoes and a center pin. The articulation in longitudinal direction of the load is in the shoes, it allows the URP of the turntable to pivot. B-type.
  • Turntables with sliding shoes and a (load carrying) ball bearing. On this type of turntables it is sometimes possible to remove the sliding shoes (on one of the turntables) and have the load suspended solely on the ball bearing. C-type.
In Figure 1, the LFP and the URP of the A-type turntable can be easily recognized. The lower chains hold the LFP secured to the transporter and the long chains together with the welded steel clips secure the URP to the load.

Bolster or TurntableFigure 1

Figure 2 illustrates the difference between A-type and B-type turntable. The pivoting sliding shoes and the rotating pin are visible between the LFP and the URP. Even though it appears that the center pin may carry some load, this is not the case. The URP pivots on the center pin, which is allowed a free vertical movement (to a certain extent) in the hole of the LFP.

Bolster or TurntableFigure 2

The turntable in Figure 3 is a C-type turntable. In the center of the turntable the ball bearing can be indicated. This ball bearing allows articulation in all directions, which makes the C-type the most versatile of turntables.

Bolster or TurntableFigure 3

There is however a principle unpredictability in the C-type turntable, for the one that has both shoes in contact with the sliding ring. The loads on the shoes and center ball bearing are statically undetermined and loads can shift (about the ball bearing) quickly from one shoe to another. This can be nerve racking to the "not so experienced" operator. The center pin of the B-type turntable is not load bearing and therefore does not have this problem.

There is a common disadvantage of the B-type and C-type turntables. During transport, both operators (front and rear transporter) are aiming to maintain their transporter level (trying to keep their pressures equalized) and could herewith be “fighting” the other operator on uneven roads or underground. Such transports should be carried out by operators that know each other in terms of how they will act and react.

The C-type turntables (since the ball bearing is load carrying) can have the sliding shoes removed of one of the turntables. This eliminates the “fighting each other” scenario, as the transporter, where the sliding shoes are removed, can now freely articulate underneath the load. The transporter, that does not have the sliding shoes removed, is to maintain the level of the load. Figure 4 shows a transport where the sliding shoes have been removed from the rear turntable. Although turntables are available in various models they all follow one of the above design concepts.

Bolster or TurntableFigure 4

Using turntables
When using two turntables, both with two shoes in contact with the sliding ring, one has effectively created a 4-point suspension scenario. As known, a 4-point suspension is prone to overloading on one point. The same applies to turntables.

To avoid this overloading, a 3-point suspension turntable was invented. This consisted of one turntable with two shoes in contact with the sliding ring and one turntable with just the center ball bearing. In practice, however, this 3-point suspension method is not being used as much as the 4-point suspension method.

When using the 4-point suspension method (sliding shoes on both turntables in place), it is common to use turntables that have an overcapacity and the overloading is not, or less of a concern, during execution of the transport. The hydraulic pressures of both transporters have to be continuously monitored and the operators should have contact with each other. As a dolly transport is normally carried out with low velocity, there is ample time for corrections.

Bolster or TurntableFigure 5

Another aspect of attention is the loading impact of the turntable on the transporter. By definition, the turntable is imposing a point load (a concentrated load) onto the transporter deck and this needs to be within the capacity of the transporter. In case the point load is too concentrated, load spreaders can be used to lengthen the loading area. Figure 5 shows a turntable on a double set of load spreaders; in this case the transporter was subject to a concentrated point load that was beyond the capacity of the transporter. Figure 6 is the transport where the turntables from Figure 3 and Figure 5 are used. The front transporter required additional load spreading that can seen on Figure 6. Between the 3rd and 4th axle the load spreading starts and between the 9th and 10th axle it stops. The rear transporter did not require any load spreading as this transporter has a higher bending moment.

Bolster or TurntableFigure 6

When to use turntables
There are a number of instances where such a configuration is desirable or even a requirement to carry out the transport.

Long loads, irrespective of weight
Long loads, irrespective of weight, that need to be maneuvered in such a way that a structure (or structures) in the surrounding area demands the maneuverability of a dolly configuration as opposed to a single transporter. Such structures can be site restrictions, trees, light posts, buildings, roundabouts etc.

Figure 7 shows the transport of a 185 ton vessel in dolly configuration due to the restrictive infrastructure. The curve (radius) of the roundabout prohibited the use of a single longer transporter. This transport was carried out in Dubai. The dolly configuration in question was 12-axle lines Cometto pull type transporter in the front (prime mover side) and 6-axle lines Cometto pull type in the rear.

Bolster or TurntableFigure 7

Loads that are long but not heavy
Loads that are long but not heavy compared to their length and do not need to be supported over their full length. In such cases, it would require more axle lines to carry out the transport without turntables than it would to carry out the transport with turntables. It is difficult, if not impossible, to give numerical guidelines to make such a determination; each load is to be engineered on a case by case basis as each case depends on size, weight and center of gravity.

Figure 8 shows the transport of a 225-ton vessel in dolly configuration due to its length. Note the distance between the front and rear transporter. This transport was carried out in Dubai. The dolly configuration consisted of a 10-axle line Cometto pull type transporter in the front and a 6-axle line Cometto pull type transporter in the rear.

Bolster or TurntableFigure 8

The above two reasons for using a dolly configuration are likely the most common reasons. However, there are two more, less common reasons for using a dolly transport configuration. When there are overhead obstructions on the transport route, such as wires, overpasses, tunnels etc and the total transport height of the cargo plus transporter plus transport beams (if any) is higher than what the overhead obstruction allows for, a different transport method is required.

Such a transport method, a transport frame, is shown in Figure 9. Turntables are used on each of the transporters, and the cargo is suspended from (hangs in) the transport frame. This allows the cargo to pass under obstructions that are just a few cm higher than the cargo itself. Note that when passing under high voltage wires additional precautions have to be taken.

Bolster or TurntableFigure 9

The last reason for using turntables is related to axle loads on a suspended surface such as a bridge. Bridge spans generally have a maximum applicable axle load as well as a maximum total weight allowed on each span. This can result in the transport combination having to spread the load a certain distance apart to comply with the bridge restrictions. A dolly configuration can offer a possible solution.

Figure 10 shows the transport of a column over a bridge. The loads between the front and rear transporter had to be spread so that the full weight was never on one bridge span. However, the column length in combination with the saddle locations did not allow for this. For that reason, the front and rear transporter travelled on different lanes. This innovative solution ensured that the loads on the bridge stayed within the limits.

Bolster or TurntableFigure 10

Figure 11 shows another transport over a (temporary) bridge where the axles have been spread. You may notice the absence of turntables in this figure which makes this transport NOT a dolly transport. The front and rear transporter are physically connected by a spine beam. This makes the transporter act as a single transporter, not as a dolly transport. The picture illustrates the spreading of the load between the front and rear part of the transporter. Another innovative solution.

Bolster or TurntableFigure 11

Note: In terms of load spreading on the bridge, it makes no difference if the configuration as shown in figure 9-11 is used or a dolly configuration with two individual transporters.

About the Author
Marco J. van Daal
Marco J. van Daal has been in the heavy lift & transport industry since 1993 starting with Mammoet Transport from the Netherlands and later with Fagioli PSC from Italy, both leading companies in the industry. His 20+years of experience extends to 5 continents and over 55 countries, and has resulted in a bestselling book “The Art of Heavy Transport” which is available on www.the-works-int.com. Marco frequently holds knowledge-sharing seminars all over the world. He currently resides in Aruba, Dutch Caribbean, with his wife and two daughters.

Lifting & Specialized Transport, April-June 2020

Click Here
To Know More / Contact The Manufacturer
Please fill in your details, we will contact you as soon as possible
Choose Title from the listPlease let us know your name.
Please let us know your Designation.
Invalid Input
Please let us know your email address.
Please let us know your City.
Please let us know your Contact Number.
Please brief your query.
Our other value-added services:

To receive updates through e-mail on Products, New Technologies & Equipment, please select the Product Category(s) you are interested in and click 'Submit'. This will help you save time plus you will get the best price quotations from many manufacturers, which you can then evaluate and negotiate.

Equipment & Machinery
Invalid Input
Building Products
Invalid Input

Spectacular heavy transport over 1,400 km in Australia: SCHEUERLE WideCombi ensures high transport efficiency for Doolan's Heavy Haulage

Australian heavy-duty specialists from Doolan’s Heavy Haulage have transported two 160-ton crusher components using WideCombi axle lines made by SCHEUERLE. Due to the low dead weight and low height of the transport Read More ...

SpeditionTrettin has relied exclusively on MEILLER tippers for generations

Hans-Otto Trettin and his son Lukas chose the right time to reorient their company, as the future of the transport business for the mining industry looked bleak with the closure of the last mines. The mainstays Read More ...

Eicher launches BS-VI solution - EUTECH6; unveils new-gen vehicles across 4.9T- 55T

Leading commercial vehicle manufacturer, VE Commercial Vehicles Limited, (VECV) unveiled its entire BS-VI range of trucks and buses across 4.9- 55T tagged with Eicher’s innovative BSVI solution - EUTECH6. The new platform Read More ...

First Cometto MSPE delivery to Taiwan

The total volume for the Taiwanese equipment manufacturer includes two 6-axle modules type MSPE 6/4/2,43 with an axle load of 40t, two power packs with an output of 110 kW each, and numerous additional accessories. The complete Read More ...

Effect of COVID-19 on Road Logistics and Impact on Movement of Goods

The Transportation sector has been one of the primary victims of COVID-19. From rickshaw pullers to the airlines, all have been affected economically by the pandemic. India's overall energy demand fell by 14% in March-April 2020 Read More ...

Goldhofer’s new »STEPSTAR« semi lowloader gives higher payloads and greater flexibility

With the »STEPSTAR« series, Goldhofer has added a new generation of self-tracking semi lowloaders to its extensive range of heavy-duty and special transport solutions. The three- to five-axle semi-trailers offer haulage Read More ...

Tiger Logistics - Handling Project Cargo with Skill & Efficiency

Tiger Logistics (India), a multimodal transport operator (MTO), is involved in transportation and custom clearance of project cargo across the country. Time and again, it has demonstrated its skills and achieved new heights Read More ...

Everest Engineering: Moving to Heavy Machines

Keen to help construct India’s high-speed railway projects, metro rails, flyovers, bridges, etc, Everest Engineering Equipment has decided to foray into the Heavy Machinery segment, informs PV Ramdev, Managing Director. What new product Read More ...

Wind Energy On The Go

As the wind generator components are becoming bigger, the challenges for the transport contractor are also becoming bigger. Where the blades used to measure 18 – 24 mtr and could be transported on extendible trailers, they can now Read More ...

Faymonville offering multi-faceted technical solutions to meet every transport challenge in North America

The Faymonville Group offers special trailers that combine cutting-edge technology with extremely practical development, especially tailored to the US market needs, at booth F.2872. HighwayMAX: The steerable 9-axle (3+3+3) HighwayMAX Read More ...

SCHEUERLE focuses on modular transporter SCHEUERLE SPMT PowerHoss

SCHEUERLE is presenting the SCHEUERLE SPMT PowerHoss with four axle lines and a diesel drive at booth F3264. These compact, self-propelled transport modules are also specialists for heavy in-house transport. So far, this operated Read More ...

Goldhofer: Moving Big Things

Visitors to Conexpo, the largest construction trade show on the American continent, will find a whole range of solutions at the Goldhofer outdoor stand (F7310A) for transporting oversized and ultra-heavy loads more easily Read More ...

India’s Logistics Space Set to Outperform Global Benchmarks

India’s logistics sector was valued at US$ 160 billion in 2018 and is expected to grow to US$ 215 billion by 2020. Today, almost 90% of cargo movement is handled by roadways and railways in the country. Globally, India has the Read More ...

LASO Transportes relies on THP/SL heavy-duty modules by Goldhofer

When the Portuguese special transport company LASO Transportes SA was awarded the contract to transport a 28,8m long and almost 165 t heavy metal component from Vale de Cambra to the port of Leça da Palmeira (about 60 km away) for shipment Read More ...

Mahindra BLAZO established as country’s most fuel-efficient truck

Mahindra Truck and Bus (MTB), a part of the USD 20.7 billion Mahindra Group, has announced that its BLAZO range of trucks has become the market leader in terms of mileage within the trucking industry. The BLAZO range has achieved Read More ...

A new Cometto ETH transporter in UK

Harsco Environmental has taken delivery of a new self-propelled transporter model ETH 8/6 for their site at Sheffield Forgemasters (South Yorkshire). The Cometto ETH 8/6 is designed for operation in steelworks with a payload Read More ...
NBM&CW

New Building Material & Construction World

New Building Material & Construction World
MGS Architecture

Modern Green Structures & Architecture

Modern Green Structures & Architecture
L&ST

Lifting & Specialized Transport

Lifting & Specialized Transport
II&TW

Indian Infrastructure & Tenders Week

Indian Infrastructure & Tenders Week